Dinamap Pro 100V2 Manual de servicio Pagina 72
- Pagina / 104
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-20 PRO 100-400 V2 Patient Monitor Service Manual Revision A
2009829-001
Calibration & Maintenance: SECTION 4. GENERAL MAINTENANCE
4.6.5. Adult Overpressure Check
1. Set up the unit and calibration equipment as shown in Figure 4-1.
2. Power on the PRO Monitor and select More...
3. Select the Service mode and input 2 2 1 3.
4. From the Service menu, select the NIBP button.
5. Select the Check button.
6. Increase applied pressure until overpressure occurs. Confirm that
pressure at the overpressure is between 300 mmHg and 330 mmHg
and the system pressure falls to less than 20 mmHg within 8 seconds.
7. Switch off the PRO Monitor and disconnect the calibration kit.
8. If the Monitor fails this test, re-calibrate the unit as described in
section 4.7.2.
4.6.6. Temperature System Check (PRO 200 & 400)
The PRO Monitor Series 200 & 400 temperature systems use
ALARIS Model 2885 and 2886 temperature probes. This system is
self-calibrating. The only maintenance required is to verify that the
temperature functions are working properly. These checks require an
IVAC probe simulator (P/N TE 1811), available from ALARIS Medical
Systems, Inc., San Diego, CA. GE Medical Systems Information
Technologies does not stock this tester.
To check the temperature system, connect the IVAC probe simulator
to the temperature probe connector on the front panel, and insert a
temperature probe into the active holster.
1. Power on the PRO Monitor.
2. Remove the temperature probe from the probe holster to initiate a
temperature reading.
Set the probe simulator to 98.6 and verify that the LCD temperature
display reads 98.6°F ±1.0°F. The numbers on the temperature LED
displays should be flashing at this point, indicating the monitor is in a
real-time monitor mode.
A range of temperatures can be checked, by using the other values
on the probe simulator (98.0, 80.2, 102.0, and 107.8).
Broken Probe Sensing
Set up the equipment and the probe simulator as in the previous
procedure. Rotate the temperature selector on the temperature
simulator to B.P. verify that the Temperature display reads 106.0°F
- PRO Series 100 - 400 V2 1
- Service Manual 1
- PRO 100-400 V2 3
- Patient Monitor 3
- PRO 100-400 Patient Monitor 5
- Table of Contents: 10
- 1 Introduction 11
- For your notes 12
- Table of Contents 13
- 2009829-001 14
- Section 1. INTRODUCTION 15
- 1.2. ADDENDA 16
- 1.4. SERVICE POLICY 16
- 1.5. EXTENDED WARRANTIES 16
- 1.6. ASSISTANCE 16
- 1.7. SERVICE 17
- 1.9. WARNINGS AND PRECAUTIONS 18
- 1.10. SYMBOL DEFINITIONS 19
- 2 Product Description 23
- Product Description: 26
- 2.1. INTRODUCTION 27
- 2.2. PRODUCT CONFIGURATIONS 27
- 2.5. COMPATIBLE PARTS 32
- 2.6. SPECIFICATIONS 34
- 2.6.3. Mechanical 35
- 2.6.4. BP 35
- 2.6.5. TURBO TEMP 36
- 2.6.6. SpO 36
- Nellcor Patents 37
- Masimo Patents 39
- 3 Theory of Operation 41
- Theory of Operation: 44
- 3.1 INTRODUCTION 45
- 3.2.4 Host Communication Port 46
- 3.3 FUNCTIONAL DESCRIPTION 47
- 3.3.4 SPO2 PWA (Optional) 48
- 3.3.6 LCD Assembly 49
- 3.3.7 Printer PWA w/Printer 49
- 4 Calibration & 53
- 4.1 INTRODUCTION 57
- 4.2. FUSES 57
- 4.3. PERIODIC MAINTENANCE 57
- 4.3.2. Power Up Checks 58
- 4.3.5. Checking Calibration 59
- 4.4 Clinician Mode 60
- 4.4.3. Clinician More... Menu 62
- 4.5. SERVICE MODE 63
- 4.5.2 Service Mode Main Menu 64
- 4.5.3. NIBP Menu 65
- 4.5.4. System Menu 66
- 4.6.1. SpO 68
- Checks (PRO 300 & 400) 68
- 4.6.2. Leak Test 69
- 4.6.3. NIBP Calibration Check 70
- 4.6.7. Printer Test 73
- plug with the 77
- 5 Schematics & Drawings 79
- Field Replaceable Parts 82
- Description Part Number 85
- PRO 100-400 Assembly Drawing 87
- Front Case Drawing 87
- Shown with Temp Assembly 87
- Page 1 of 3 87
- Page 2 of 3 88
- Shown with Masimo Board 89
- Page 3 of 3 89
- Rear Case Drawing 90
- Page 1 of 4 90
- Page 2 of 4 91
- Pnuematic Assembly Drawing 92
- Page 3 of 4 92
- Pneumatic Hose Routing 93
- Page 4 of 4 93
- Sheet 1 of 9 94
- Sheet 2 of 9 95
- Sheet 3 of 9 96
- Sheet 4 of 9 97
- Sheet 5 of 9 98
- Sheet 6 of 9 99
- Main Board Assembly 100
- P/N: 2008238-001 C 100
- Sheet 7 of 9 100
- ISOLATED POWER SUPPLY 101
- HOST INTERFACE CONNECTOR 102
- SPO2 PATIENT CONNECTOR 102
- SPO2 MODULE CONNECTOR 102
- 2009829-001 A 104
Relacionado con productos y manuales para De medición, control y control Dinamap Pro 100V2
(108 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales